The hot water coming out of a faucet is what many homeowners take for granted. We use the water to rinse dishes, clean food, wash our bodies, and perform routine tasks. However, this reliable plumbing system may occasionally encounter unexpected issues. When we suddenly have no hot water supply in our homes, it can cause disruptions and inconveniences to our everyday activities. hot water heater repair
Sometimes, we may turn on the hot water faucet and discover it is not working correctly. Maybe there’s no water coming out of the tap at all. Or perhaps there is water, but it comes at a freezing cold temperature. Either way, troubleshooting a faulty faucet can perplex many homeowners. The best solution is to contact a professional plumber for assistance.
There are many reasons why the hot water faucet is not working. The possible explanations may range from frozen pipes to issues with the water tank. Here are four common causes for no hot water coming out of a faucet:
CLOGGED PLUMBING
When a faucet fails to provide hot water, check to see whether the other faucets in your home are affected. Go around and test each one one at a time. Is there hot water in the kitchen, bathroom, or elsewhere in the house? If the other faucets are still operational, your plumbing issue is limited to a single faucet.
One possible explanation is that your faucet is clogged. Mineral deposits accumulate inside plumbing fittings over time as a result of repeated use. This obstruction prevents hot water from flowing properly. When combined with other plumbing concerns, such as poor water pressure, the problem becomes more pronounced. A plumber can assist you in clearing the debris and reactivating the hot water faucet.
AIRLOCK
Air can become caught in the pipes at times, resulting in a partial or complete obstruction of the faucet. Because of a lack of pressure inside the hot water pipes, these air pockets may not be pushed out. Because cold water is frequently connected directly from the main water line, there is increased pressure. As a result, it is less likely to be affected by the airlock. As a result, cold water may be pouring out of the hot water side of the faucet.
It could be able to remove an airlock from the faucet. Connect one end of a hosepipe to the cold water faucet and the other end to the hot water faucet. Use a clamp to secure this connection. Turn on the hot water first, followed by the cold water. The pressure from the cold-water faucet should assist in moving the airlock. Before turning off the cold water, let it on for 30 seconds. Repeat this method several times to get the air out of the line.
FROZEN PIPES
If you reside in a cold climate, your water pipes are more likely to freeze during the winter. A frozen pipe implies that water is unable to reach your faucets. Even if this is simply a temporary issue, it may have an impact on how you use the hot water faucet.
You should insulate your pipes before winter to reduce the chances of them freezing. If your pipes are frozen, you can warm them up with a hairdryer, heat gun, or heating pad. With enough heat, the pipes may unfreeze and the water may begin to flow again. Make sure you winterize the pipes before the next cold front arrives to avoid this problem happening again.
HOT WATER TANK
Sometimes your faucet works absolutely fine, but the real trouble is the hot water tank. The hot water shortage could be caused by a variety of factors. Check that there is power to the appliance and that no fuses have blown before using an electric heater. There could possibly be a problem with the thermostat or the heating elements.
To heat the water, a gas water heater will use propane or natural gas. The fuel is sent to the gas control valve via the supply line, which transmits a little amount of gas to keep the pilot light burning. This heats the thermocouple, which sends a signal back to the control valve, which activates the burner.
Start by checking the pilot light if there is no hot water. It should always be turned on. Otherwise, relight it. Inspect the thermocouple as well. It could be filthy from soot accumulation, misaligned, or altogether broken. If the pilot light and thermocouple look to be in good working order, check the gas valve to ensure it is open and the gas is flowing. If not, you should contact an Oshawa plumber to look into the problem.
Comments 0